20-102931 ABDULLEN100CLIENT INFO:ABDULLE FAMILYsabdule@gmail.com32222 8TH AVE SWFEDERAL WAY WA98023SHEET:
SCALE:NOTESDRAWINGS PROVIDED BY:ALEX BERGMANA.R.BERGMAN 3602800528A.R.BERGMAN101@GMAIL.COMTACOMA, WA DATE:
7/28/2020
1 OF
SHEET #:32222 8TH AVE SWFEDERAL WAY WA980235
G E N E R A L N O TE S
D O N O T D E TA C H
PLAN THEFT PROTECTION
This plan is copywrited and all rights are reserved including the right of reproduction in
part or whole, except by A.R.BERGMAN DRAFTING & DESIGN LLC, this plan is not to be
reproduced by anyone by any method including blueprinting, photocopying, photography,
tracing, redrawing, or any other means. this plan may not be listed by anyone for repeat
construction, on brochures, advertising, or any other purpose without written consent of
A.R.BERGMAN DRAFTING & DESIGN LLC . This plan may not be knowingly furnished to
others for such purposes.
a. The right of building only one structure from the plan you have purchased is granted
exclusively to the owner and their building contractor. Unlawful reproduction of this plan
absolves A.R.BERGMAN DRAFTING & DESIGN LLC from all responsibility as to the
accuracy of the drawings. And we may take suitable legal action against the copier
under copyright laws.
b. If any building is constructed from this plan other than the one for which the plan was
purchased, we have the right according to copyright law to recover the value of the
building less the cost of construction.
NAILING SCHEDULE
(See IBC Table 2304.9.1)
Joist to sill or girder 3-8d
Bridging to joist, each end 2-8d
Sill plate to joist or blocking 16d @ 16" ac
Top laid stud 2-16d
Doubled stud 16d @ 24" ac
Doubled top plate 16d @ 16 ac
Top plates, laps, and interx. 2-16d
Ceiling joist to plate 3-8d
Continuous header to stud 4-8d
Ceiling joists, laps over partition 3-16d
Built up corner studs 16d @ 24" ac
SPECIFICATIONS
Do not scale any drawings in this document
All construction shall be in compliance with the IRC 2015
All dimensions shall take precedence over scale shown on plans, sections,
and details
Notes and details on drawings shall take precedence over general notes
and typical structural details
Material notes and specifications on the drawings shall take precedence
over the specifications
All edges ot rescue windows from sleeping rooms have a minimum net
opening of 5.7 sq. ft. and a minimum height of 24" minimum width shall be
20" egress and rescue from sleeping rooms shall have a sill height of not
more than 44"
CODES AND STANDARDS
All workmanship is to be of a standard equal in all respects to good building practice.
At the time of preparation, this plan was drawn in accordance with the current editors
of the IRC 2015. It is the responsibility of the owner builder to insure that changes to the
code are complied with and all amendments are incorporated in the construction of this
plan. All work shall conform to local building codes and by laws that may take
precedence.
Prior to proceeding with construction, the builder must verify all information,
dimensions, and specifications of this plan. Written dimensions always take precedence
over scaled measurements.
Any variances from the structural drawings or specifications or from conditions
encountered at the job site shall be resolved by the owner builder and such solutions
shall be their sole responsibility.
The owner builder shall be responsible for the correct siting of the house on the property
and for confirmation of all requirements for siting. A.R.BERGMAN DRAFTING & DESIGN
LLC can accept no responsibility for plans not complying with the local side yards and
setbacks of a specific piece of property.
The owner builder to supply all mission missing dimensions on site plan, also elevations
of lot, legal description, north direction, main streets and location of services.
A.R.BERGMAN DRAFTING & DESIGN LLC shall not be responsible for conditions such as
soil bearing capacity, depth of frost penetration, water table, buried structures, etc.
A.R.BERGMAN DRAFTING & DESIGN LLC does not assume liability for any errors or
omissions prior to commencement of construction.
Any variances from the structural drawing and specifications are the sole responsibility
of the owner builder. A.R.BERGMAN DRAFTING & DESIGN LLC shall not be responsible
for any such variance made or advised by any official, builder, or other person and any
such variance nullifies any responsibilities that A.R.BERGMAN DRAFTING & DESIGN LLC
may have with respect to this plan or consequent construction.
All requirements weather general or specific, shall be interpreted in conjunction with all
other information appearing in the drawings and specifications.
CONCRETE & FOUNDATIONS
All concrete to have a minimum compressive strength of 3000 PSI at 28 days
Concrete footings must be placed on undisturbed or compacted soil per IRC. Footings
shown on these drawings have been designed for soil bearing capacity of 1500 PSF.
Unless otherwise shown or noted, concrete coverage for reinforcing bars to face of bar
shall be as follows:
1- concrete in contact with earth uniformed - 3 inches
2- Concrete in contact with earth formed - 3 inches
3- Wall, exterior face - 2 inches
4- Wall, interior face - 3/4 inches
5- Structural slabs 3/4 inches
All reinforcements shall be positioned into concrete as per engineers details.
Inserts shall be well secured in position prior to placing concrete.
Refer to structural engineers notes for additional information.
FRAMING
Roof design load (Live and Dead) - 25 PSF
Floor design load (Live and Dead) - 40 PSF
Balcony deck design load (Live and Dead) - 60 PSF
Stair (Live and Dead) - 200 psf
Framing lumber shall be number two (2) Douglas Fir unless otherwise specified on plan. All beam and lintel sizes shown on the
drawing are based on number two (2) Douglas Fir unless otherwise specified.
Floor and roof sheathing to be laid continuous over two or more spans and face perpendicular to supports. Allow min. space 1/16"
between end joints and 1/8" between edge joints for expiation and contraction of panels.
Joists are to be doubled under parallel partitions.
Joists shall be placed to accomodate heating and plumbing etc.
All headers and trimmers to comply with IRC 2015.
Refer to structural engineers notes for additional information.
Owner builder to obtain certifigate from manufacturer of floor trusses, roof trusses, and glu-lam beams
Wood in contact with concrete shall be pressure treated.
New dimensions are from face of stud.
ROOFING
All roofing shall be applied according to the manufacturers recommendations.
Trusses:
Truss manufacturer shall furnish shop drawings showing calculations , all truss conditions connections and spacing. Design
roof load as per truss manufacturers engineer.
No truss shall be field modified without prior approval of building department.
SHEET METAL
Provide and install sheet metal ducts from all hoods and exhaust fans outside
All required flashing to be 26 gauge galvanized metal unless otherwise specified.
PLUMBING
Provide and install plumbing and fixtures as indicated on plans according to local plumbing codes.
ELECTRICAL/ HEATING
Installation of entire heating system shall comply with manufacturers directions when applicable and conform with local
building codes and regulations in all respects.
Installation of all electrical items must comply with local electrical codes and regulations and with local electrical power
supply regulations in all aspects.
Outlet locations shown on plans comply with or exceed National Electrical Code requirements and are to be used as a guide
only. Adjust according to owner and local authorities requirements.
Approved heat smoke detectors to be installed as required per IRC 2015
GLASS
Glass weights to comply with IRC 2015
If glass sliding patio doors are installed, they must be of tempered glass.
Glass other than safety glass shall not be used for a shower or bathtub enclosure. All work shall comply with IRC 2015
Refer to drawing for specification
CABINETS
Field verify all cabinet dimensions prior to fabrication.
Kitchen counter top should be 36" / 42" with 4" splash.
Bath or counter top should be 30" with 4" splash and return.
MISCELLANEOUS
Caulk over and around all exterior openings using non hardening caulk compound.
Flash all changes of material on exterior walls.
Flash over all exterior openings.
All siding or stucco to be a minimum of 6" above finished grade.
All balcony railings to be 36" in height. Maximum spacing between vertical members
such that a 4" diameter sphere can not pass through
Floor finishes, bathroom vanities, backsplash, and kitchen cabinets to meet
specifications of owner builder.
Coat closets should have at least one rod and shelf. Linen shelf shall have 5
adjustable shelves whenever possible.
Ceramic and plastic tiles installed on walls around bathtubs or showers shall be
applied over moisture resistant backing.
All nails used in the exterior trims or sidings shall be galvanized or aluminum.
Use cooler nails at 7" o.c. on all studs, plates, and blocking use 5d nails with 1/2"
wallboard and 6d nails with 5/8" unless otherwise noted.
Type and thickness of gypsum wall board as per drawings, all work to meet with
manufacturers requirements.
Ceiling insulation may be loose fill type or batt type, wall and floor insulation must be
batt type.
Walls and ceilings between residence and attached garage shall be insulated.
Insulation requirments may vary with heating system and local conditions. Please
check with local authorities.
All roof spaces shall be ventilated with soffit roof or gable vents or a combination of
these equally distributed between the top or roof space and soffits.
All ventilation of crawlspace and roof spaces to conform to IRC 2015
A .R .B E R G M A N D R A F TIN G & D E S IG N
RECEIVED
CITY OF FEDERAL WAY
COMMUNITY DEVELOPMENT
Aug 07 2020
8TH AVE SWEXISTING
HOUSE 2100
S.F. +/-EXISTING
DRIVE/WALK
WAY 780 S.F. +/-
EXISTING
CONC. PATIO
1200 S.F. +/-
PL 120.00'PL 70.00'PL 120.00'PL 70.00'325'
320'
330'
315'EXISTINGGARAGETO FINISH380 S.F. +/-step
step
2X 2X8 TYP HDR.
S100CLIENT INFO:ABDULLE FAMILYsabdule@gmail.com32222 8TH AVE SWFEDERAL WAY WA98023SHEET:
SCALE:SITE PLANDRAWINGS PROVIDED BY:ALEX BERGMANA.R.BERGMAN 3602800528A.R.BERGMAN101@GMAIL.COMTACOMA, WA DATE:
7/28/2020
2 OF
SHEET #:32222 8TH AVE SWFEDERAL WAY WA980235
SITE INF O
PARCEL#: 9264920460
OWNER NAME: ABDULLE SAFIA AND SHIFOW AM
PROJECT ADDRESS: 32222 8TH AVE SW
FEDERAL WAY, WA 98023
PERMITTING JURISDICTION: CITY OF FEDERAL WAY
LOT SIZE: 8,146S.F.
BUILDING AREA EXISTING : 2260 S.F.
PROPOSED AREA: 0 S.F.
SECT/TOWN/RANGE: NW-18-21-4
LEGAL DESCRIPTION: WEST CAMPUS DIV 3
PLat Block:
Plat Lot: 46
LEGEND
EXISTING STRUCTURE
ROAD
PAVED SURFACE
PROPERTY LINE
SETBACK
5' CONTOUR
SITE PLAN
1" = 10'-0"
NOR THNORTH
PROJECT LOCATION
VICINITY MAP
N.T.S.
NO R THNORTH
AREA OF WORK
A .R .B E R G M A N D R A F TIN G & D E S IG N
RECEIVED
CITY OF FEDERAL WAY
COMMUNITY DEVELOPMENT
Aug 07 2020
WH
9080 9080
CRAWL ACCESS 21"X28"6030LS4568
UP
6x14 Beam
EP
24'-0"15'-0"12'-0"27'-8 1/2"12'-0"23'-0" X 27'-9"
GARAGE
1122
stepstep
DOOR SCHEDULE
NUMBER WIDTH HEIGHT DESCRIPTION
D01 30 "80 "HINGED-DOOR P04
D02 36 "80 "HINGED-DOOR P04
2X 2X8 T YP HDR.9'-0"5MIL. VAPOR BARRIER
2X10 16" O.C. W/ BLOCKING
R-49 INUL.
2X10 RIM JOIST
3/4" T&G GLU. & NAILD.
1 1/2" R7.5 POLYSTYRENE INUL. @
ALL CONC. STEP WALLS
5MIL. VAPOR BARRIER BENEATH
2X6 FURRED OUT WALLS
R-21 INSUL.
1/2" GWB. FINISH
2X6 FURRED OUT WALL S
R -21 INSUL.
1/2" GWB. INTERIOR FINISH
NEW 2X6 FURRED WALL BEYOND
CONC. S TEP WALL FURRING
DBL. TOP PL ATE
5 MIL. VAPOR BARRIER ALL CONC.
SURFACES
SPRAY FOAM SEAL ANT ALL SILL TO
CONC. LOC.
EXIS TING CONC. FOUND. WALL.
SILL PL ATE
1 3/4" FURRING AS NEEDED
R -49 INSUL.
5/8" GWB. ON CLG.
2" THK. HIGH DENSIT Y R -7.5 INSUL. MIN.
SPRAY FOAM SEAL ANT ALL SEAMS AND EDGES
6 MIL. VAPOR BARRIER
3/4" T&G PLYWD. GLU. & NAILED
P.T. 2X4 SLEEPERS 16" O.C.
L AP SPLICES 12" MIN., RUN 6" MIN UP SIDES
WH
CRAWL ACCESS 21"X28"
D02D02
D01D01
UP
6x14 Beam
EP
S1
A100
S1
A100
SECTION
24'-0"15'-0"27'-8 1/2"12'-0"1'-6 1/2"3'-6"3'-0"4'-10"4'-1 1/2"13'-7"5'-8"
5'-2" X 7'-7"
22'-8" X 24'-1"
17'-4" X 4'-6"
DEN
STAIRWAY
UTILITY
step
step
2X 2X8 T YP HDR.
A100CLIENT INFO:ABDULLE FAMILYsabdule@gmail.com32222 8TH AVE SWFEDERAL WAY WA98023SHEET:
SCALE:REMODEL PLAN / SECTIONDRAWINGS PROVIDED BY:ALEX BERGMANA.R.BERGMAN 3602800528A.R.BERGMAN101@GMAIL.COMTACOMA, WA DATE:
7/28/2020
3 OF
SHEET #:32222 8TH AVE SWFEDERAL WAY WA980235
EXISTING GARAGE
1/4"= 1'-0"
NO R THNORTH
PROPOSED DEN PLAN
1/4"= 1'-0"
NO R THNORTH
WALL LEGEND
EXISTING WALL TO REMAIN
EXISTING WALL TO BE REMOVED
CROSS SECTION
1/2"= 1'-0"
NEW 2X6 STUD WALL 16" O.C. ON P.T. SILL R-
21, AIR GAP, 1/2" GWB. INTERIOR FINISH
NEW FURRED 2X6 STUD WALL 16" O.C. ON P.T.
SILL R-21, AIR GAP, 1/2" GWB. INTERIOR
FINISH
CONSTRUCTION NOTES
6ML. VAPOR BARRIER THROUGH OUT SLAB. ALL STEPPED CONC. WALLS.
SPRAY FOAM SEALANT ALL CONC. TO SILL INFILTRATION LOCATIONS.
P.T. 2X4 SLEEPERS @ 16" O.C.,R-7.5 HIGH DENSITY INUL. MIN. P.T. SHIM AS REQ. TO LEVEL. 3/4" T&G PLYWD. GLU &
NAILED.
MAINTAIN WINDOW OPENINGS & ELECTRICAL PANEL ACCESS
FUR CLG. JOIST AS REQ. TO 2X12, R-49. INSUL. 5/8" GWB. FINISH.
FRAME WALL BEHIND GARAGE DOOR TO COMPLY WITH HOA COVENANT. REMOVE GARAGE DOOR HARDWARE AS
NEEDED.
CONSTRUCTION NOTES
11
22
REMOVE EXISTING BIFOLD DOOR
REMOVE EXISTING DEMISING WALL
A .R .B E R G M A N D R A F TIN G & D E S IG N
RECEIVED
CITY OF FEDERAL WAY
COMMUNITY DEVELOPMENT
Aug 07 2020